Matt 2:1

Matt acrylic clearcoat

Variants

ColourArt. No.Capacity Quantity per carton
transparent63011 l6
Hardener
matt 1:263000,5 l6

Gloss grade

matt
Matt 2:1

Technical documentation

Weight/Volume Calculator

mlg
Varnish
Hardener:00
Total of mixture00
Minimum thinner0%00
Total of mixture00
Maximum thinner0%00
Total of mixture00
Thinner value %00
Warning: Value is not within the tolerance given by the manufacturer. (Min: , Max: ).
Total of mixture00

Video

Description

High-quality matt acrylic clearcoat with a special effect. Intended for specialized repairs of car body parts that require a matt finish. It allows to obtain an evenly matt surface as well as a strong and durable finish.

Matt 2:1 Clearcoat can be mixed with Inter Troton Crystal and Zircon clearcoats, as well as with Multi Füller MS 2:1. Different degrees of matt are obtained depending on mixture ratios.

Degrees of the matting effect

matt

Advantages

  • Perfect matt finish.
  • Very good flow and levelling.
  • Durable coating.
  • Increased resistance to scratches SR (Scratch Resistant).

Substrates

MATT 2:1 2K acrylic clearcoat can be applied over:

  • Base coats.
  • Old coatings in good condition after sanding and degreasing.

Important informations

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    Mixing ratio
    2 : 1 + 10%

  • Lepkość natryskowa

    Spraying viscosity
    16 ÷ 18s / 20°C

  • Żywotność mieszanki

    Pot life
    ~ 7h /20°C

  • Liczba warstw

    2 layers
    HVLP / RP
    ø1,3 ÷ 1,4 mm

  • Czas odparowania

    between layers
    10 ÷ 15 min

  • Czas utwardzania

    Hardening time
    24 h / 20°C

  • Zamieszać

    Caution: Stir well before using.

Application process

  • Zastosowanie
  • Use

    Fast car body repairs that required matt durable finish.

  • Proporcje mieszania
  • Mixing ratio by volume

    Clearcoat: 2
    Hardener: 1
    Thinner: 10%

  • Lepkość natryskowa
  • Spraying viscosity

    16÷18 seconds at 20ºC

  • Żywotność mieszanki
  • Pot life for the mixture

    About 7 hours at 20ºC

  • Liczba warstw
  • Number of layers

    2 full layers, total dry film thickness of approx. 50-60 μm

    RP gun parameters
    Nozzle: 1.3÷1.4mm; Pressure of input: 2.0÷2.2 bars.
    HVLP gun parameters
    Nozzle: 1.3÷1.4mm; Pressure of input: 2.0 bars.

    Note: Follow the gun producer’s recommendations.

  • Czas odparowania
  • Flash off time

    Between layers: about 10÷15min.

  • Czas utwardzania
  • Hardening time

    Dust dry: 30 minutes at 20ºC
    Touch dry: 24 hours at 20ºC

    Temperatures below 20°C significantly increase the drying time.

  • Informacja
  • Performance

    1 liter of the mixture is enough to paint 8÷9 m2 of surface with a layer thickness of 50 μm.

  • Informacja
  • Polishing and eliminating defects

    Caution: Do not polish matt coatings!

  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar.
    • When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product



    

    Related products

      
    See also other products
    Wyjście 
    Go to top