HS 2:1

Acrylic clear coat

Variants

ColourArt. No.Capacity Quantity per carton
transparent57501 l6
transparent57515 l4
Hardener for clear coat
standard5754 0,5 l6
standard57552,5 l4

Gloss grade

high gloss
HS 2:1

Technical documentation

Weight/Volume Calculator

mlg
Primer
Hardener:00
Total of mixture00
Minimum thinner0%00
Total of mixture00
Maximum thinner0%00
Total of mixture00
Thinner value %00
Warning: Value is not within the tolerance given by the manufacturer. (Min: , Max: ).
Total of mixture00

Video

Description

High quality bicomponent acrylic transparent clear coat for fast repairs with low content of volatile compounds and increased scratch resistance (SR). Clear coat for universal use- works good for spot repairs as well as for full body car repairs.

Advantages

  • High content of solid.
  • Short hardening time.
  • Very high gloss.
  • Easy to apply.
  • Very durable and high resistante.

Substrates

Acrylic Clear Coat 2:1 can be applied over:

  • Base coats.
  • Old finishes in good condition after matting and degreasing.

For dulling the color we recommend the following :

  • grey abrasive cloth with matting compound.
  • sanding paper with gradation of 600÷800 (for dulling on wet).
  • sanding paper with gradation of  360÷400 (for dulling by machine).

Important informations

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    Mixing ratio
    2 : 1 + max. 10%

  • Lepkość natryskowa

    Spray viscosity
    15 ÷ 16s / 20°C

  • Żywotność mieszanki

    Pot life
    2 h / 20°C

  • Liczba warstw

    2 full layers
    HVLP / RP
    ø1,3 ÷ 1,4 mm

  • Czas odparowania

    between layers
    approx. 5÷7 min.

  • Czas odparowania

    before baking
    approx. 5÷10 min.

  • Czas utwardzania

    Hardening time
    15 min. / 20°C
    30 min. / 60°C
    (for standard hardener)

Application process

  • Zastosowanie
  • Use

    For car body repairs that require a durable finish.

  • Proporcje mieszania
  • Mixing ratio by volume

    Clear Coat: 2
    Hardener: 1
    Thinner: max. 10%

  • Lepkość natryskowa
  • Spraying viscosity

    15÷16 seconds at 20°C.
    With 10% thinner

  • Żywotność mieszanki
  • Pot life

    Approx. 2 hours at 20°C.

  • Liczba warstw
  • Number of layers

    2 full coats, approx. 60 µm of dry film.
    RP gun Parameters
    Nozzle: 1.3÷1.4 mm; Pressure: 2,0÷2,2 bar.
    HVLP gun Parameters
    Nozzle: 1.3÷1.4 mm; Pressure inside the nozzle: 2,0 bar.
    Follow the gun producer’s instructions.

  • Czas odparowania
  • Evaporation time

    Between layers: about 5-7 minutes
    Before baking: about 5-10 minutes

  • Czas utwardzania
  • Curing time

    At 20°C
    Dust free: after about 15 minutes.

    Baking at 60°C – 30 minutes
    ready to polish after drying overnight

    Temperatures below 20°C significantly decrease the drying time.

  • Suszenie promieniem IR
  • IR Drying

    15 ÷ 20 minutes of short waves, depending on the layer thickness and the type of radiator.
    Do not exceed 60°C.
    Use as recommended by the equipment manufacturer.
    Wait about 10 minutes before starting the heater drying.

  • Informacja
  • Product efficiency

    1 liter of mixture is enough to cover approx. 8-10 m2 with a dry layer of 60 μm of thick dry layer.

  • Informacja
  • Shading

    Make sure you have covered the whole area with the base coat and do the shading only on a previously prepared area. Use FADE OUT THINNER to blend the dust that has settled around the repaired surface and to eliminate optical gloss differences between the old lacquer and the newly applied acrylic clear coat.

  • Informacja
  • Polishing and removing impurities inclusions

    Usually polishing is unnecessary, as the HS 2:1 Acrylic Clear Coat gives the surface a perfect look immediately after use. However, if some dirt inclusions appear, we recommend removing them and polishing the surface with an abrasive compound.

  • Informacja
  • General notes
    • Do not exceed recommended doses of hardener!
    • The best repair results can be achieved at room temperature. Temperature in body shop and temperature of a product should be the same.
    • When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and respiratory system.
    • Clean the guns and equipment immediately after use.
    • The rooms should be well ventilated.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product



    

    Related products

      
    See also other products
    Wyjście 
    Go to top