Soft

Soft and filling polyester putty

Variants

ColourArt. No.CapacityQuantity per carton
cream-colored1131 250 g12
cream-colored1109400 g18
cream-colored11271 kg10
cream-colored1108 1,8 kg10
cream-colored1248 4,3 kg4

Gloss grade

matt
Soft

Technical documentation

Video

Description

2-component soft sanding and high filling polyester putty designed for car repairs. Recommended for filling large dents and holes. Can be applied in thick layers with no sagging. Due to its flexibility, it is perfect for creating shapes and filling dents on surfaces with complex contours.

Advantages

  • Easy to mix and apply.
  • Proper hardness with good elasticity.
  • Good sanding properties.

Substrates

The product has very good adhesion to various surfaces. It can be applied over:

  • Bare steel and aluminum after flatting and degreasing,
  • Zinc coated steel after flatting and degreasing,
  • Sanded glass fibre (GFK/GRP), polyester putties, acrylic and epoxy primers and existing coatings in good condition,
  • Well sanded old and factory top coats.

We recommend sandpaper with gradations: P80÷P120.

Caution:  Do not apply the putty directly on the reactive primers, 1K acrylic and nitrocellulose products.

Important informations

  • Przetrzeć odtłuścić

    degrease

  • Mieszanie wg wagi

    Mixing ratio by weight
    100 : 2

  • Czas życia

    Pot life
    4 ÷ 7 min. / 20°C

  • Czas utwardzania

    Drying time
    20 ÷ 30 min / 20°C

  • Szlifowanie

    P80 ÷ P120
    P120 ÷ P320

Application process

  • Zastosowanie
  • Use

    Soft sanding polyester putty for car repairs.

  • Mieszanie wg wagi
  • Mixing ratio by weight

    Putty: 100 parts
    Hardener: 2 parts

    Stir thoroughly until achieving homogenous paste. Be careful not to create air inclusions.

  • Czas życia
  • Layer thickness

    Putty can be applied in several thin coats. After each of them the product should cure. Do not exceed the thickness of 5 mm

    Pot life is 4÷7 minutes at 20°C

  • Czas utwardzania
  • Hardening time

    20÷30 minutes at 20°C.

    Temperature below 20°C significantly increases the hardening time.

  • Szlifowanie
  • Sanding
    • Coarse sanding (dry): P80÷P120,
    • Finishing sanding (dry): P120÷P320.
  • Suszenie promieniem IR
  • IR drying

    5÷7 minutes of short waves, depending on the layer thickness and the type of radiator.
    Do not exceed the temperature of 60°C.
    Use as recommended by the equipment manufacturer.

    Caution: Wait about 5 minutes before the IR drying process.

  • Informacja
  • Further work

    Polyester putties can be over coated with:

    • 2K polyester putties.
    • 2K polyester spray fillers.
    • 2K acrylic fillers.
    • 2K epoxy fillers.
  • Informacja
  • General notes
    • Excessive amount of hardener will cause problems with bleaching of the topcoat!
    • When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and respiratory system.
    • Clean the guns and equipment immediately after use.
    • The rooms should be well ventilated

    Caution: To maintain safety, always follow the instructions given in the MSDS for
    the products.

Ask about this product



    

    Related products

     

    Read more about the product on the blog

    
    See also other products
    Wyjście 
    Go to top