Anticorrosive Isolation Primer 3:1

Anticorrosive Isolation Primer

Variants

Colour Art. No. CapacityQuantity per carton
grey21140,75l + 0,25l6
white112570,75l + 0,25l6
black112580,75l + 0,25l6

Gloss grade

matt
Anticorrosive Isolation Primer 3:1

Technical documentation

Weight/Volume Calculator

mlg
Primer
Hardener:00
Total of mixture00
Minimum thinner0%00
Total of mixture00
Maximum thinner0%00
Total of mixture00
Thinner value %00
Warning: Value is not within the tolerance given by the manufacturer. (Min: , Max: ).
Total of mixture00

Video

Description

High quality 2K acrylic primer with anti-corrosion additives. It is a perfect isolating primer for car repairs. Perfetly protects sanded bare steel and isolates difficult surfaces and putties from topcoats, preventing mapping effects. Ideal spreading and fast drying time allows primer to be applied wet on wet. Does not require sanding.

Advantages

  • Very good anticorrosive protection. of steel surfaces.
  • Strong adhesion to various substrates.
  • Very good isolating properties.
  • Short hardening time.
  • Suitable for wet on wet application.

Substrates

Wet on Wet Acrylic Primer 3:1 can be applied over:

  • Steel and aluminum after flatting and degreasing.
  • Zinc coated steel and galvanized steel after flatting and degreasing. S
  • anded glass polyester laminates (GFK/GRP). P
  • olyester body fillers and putties
  • Epoxy primers.
  • Wash primers.
  • Old coatings in good condition.

Important informations

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    Mixing ratio
    3 : 1 + 20%
    3 : 1 + 35%

  • Lepkość natryskowa

    Spraying viscosity
    ~30s / 20°C
    17÷19 s / 20°C

  • Żywotność mieszanki

    Pot life
    40 min. / 20°C

  • Liczba warstw

    1 ÷ 2 x 1
    HVLP / RP
    ø1,2 ÷ 1,6 mm
    (for sanding)

  • Liczba warstw

    1,5 x 1
    HVLP / RP
    ø1,2 ÷ 1,6 mm
    (wet on wet)

  • Czas odparowania

    between layers
    5 ÷ 10 min.
    20 ÷ 30 min.

  • Czas utwardzania

    2÷3 h / 20°C
    15 ÷ 20 min. / 60°C

  • Szlifowanie na sucho

    P360 ÷ P500

  • Szlifowanie na mokro

    P600 ÷ P1000

Application process

  • Zastosowanie
  • Use

    For car repairs as an isolation primer for sanding or wet on wet application.

  • Proporcje mieszania
  • Mixing ratio by volume

    Primer: 3
    Hardener: 1

    Thinner:

    • 35% for wet on wet,
    • 20% for sanding.

    Mix thoroughly until a homogeneous consistency is obtained.

  • Lepkość natryskowa
  • Spraying viscosity

    17÷19 seconds at 20°C thinner 35%
    about 30 seconds at 20°C thinner 20%

  • Żywotność mieszanki
  • Pot life for the mixture

    about 40 minutes at 20ºC

  • Liczba warstw
  • Number of layers

    For wet on wet: 1,5 layers; about 30µm of dry layer.
    For sanding: 1÷2 layers; about 50µm of dry layer.

    RP gun parameters:
    RP Nozzle: 1.2÷1.6 mm; Pressure of input: 2.0÷2.2 bars.
    HVLP Nozzle 1.3÷1.5 mm; Inlet pressure: 2.0 bars

  • Czas odparowania
  • Flash off time

    Between layers: about 5÷10 minutes
    before applying solvent base system: approx. 20 minutes
    before applying water base system: approx. 30 minutes

    Flash off time depends on the temperature and the number of layers

  • Czas utwardzania
  • Hardening time for Isolation primer (30÷50 µm)
    • at 20°C: ready for sanding after 2÷3 hours.
    • at 60°C (facility temperature): ready for sanding after baking for about 15÷20 minutes cooling (approx. 1 hour).

    Temperature below 20°C significantly increases the hardening time.

  • Suszenie promieniem IR
  • IR drying

    Isolation primer /30-50 µm/ : 5÷7 minutes under short waves.
    Primer for sending /50÷100 µm/: 8÷10 minutes under short waves.

    Do not exceed 60°C. Use as recommended by the equipment manufacturer. Wait about 10 minutes before starting IR drying.

  • Szlifowanie na sucho
  • Dry sanding

    Machine sanding: P360÷P500.
    Manual sanding: P320÷P500.

    Wet on wet does not require sanding

  • Szlifowanie na mokro
  • Wet sanding

    Machine sanding: P600÷P1000.
    Manual sanding: P800÷P1000.

    Wet on wet does not require sanding

  • Informacja
  • Further work

    2K acrylic fillers can be directly over coated with:

    • 2K top coats.
    • 1K base coats.
    • 2K polyester putties
    • 2K acrylic primers
  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved at room temperature. The temperature in the body shop and the temperature of the product should be similar.
    • When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and air ways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product



    

    Related products

    

    Check product tips

     
    See also other products
    Wyjście 
    Go to top