TIX HS 2:1

Acrylic clearcoat

Variants

ColourArt. No.CapacityQuantity per carton
transparent169331 l6
transparent169375 l4
Hardener for clearcoat
standard169340,5 l6
standard169382,5 l4
fast169350,5 l6
fast169392,5 l4

Gloss grade

high gloss
TIX HS 2:1
New

Technical documentation

Weight/Volume Calculator

mlg
Varnish
Hardener:00
Total of mixture00
Minimum thinner0%00
Total of mixture00
Maximum thinner0%00
Total of mixture00
Thinner value %00
Warning: Value is not within the tolerance given by the manufacturer. (Min: , Max: ).
Total of mixture00

Description

High-quality 2K acrylic clearcoat with increased scratch restistance (SR – Scratch Resistant) for automotive repairs. It features a hard and durable high-gloss finish,  exceptionally easy application, and outstanding anti-sagging properties.

Advantages

  • Excellent stability on vertical surfaces minimizing the risk of runs.
  • Very easy application.
  • High gloss and excellent coating appearance.
  • Hard and durable finish.
  • Suitable for both spot repairs and full-body painting.

Substrates

Acrylic clearcoats can be applied over:

  • Basecoats.
  • Old paint coatings in good condition after matting and degreasing.

Important informations

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    Mixing ratio
    2 : 1 + 20 ÷ 25 %

  • Lepkość natryskowa

    Spraying viscosity
    16 ÷ 18s / 20°C

  • Żywotność mieszanki

    Pot life
    6 ÷ 8 h / 20°C

  • Liczba warstw

    2 layers
    HVLP / RP
    ø1,3 ÷ 1,4 mm

  • Czas odparowania

    between layers
    5 ÷ 10 min.

  • Czas odparowania

    before baking
    about 15 min.

  • Czas utwardzania

    Curing time
    30 min. / 60°C

Application process

  • Zastosowanie
  • Use

    Car body repairs that required durable finish.

  • Proporcje mieszania
  • Mixing ratio by volume

    Clearcoat: 2
    Hardener: 1
    Thinner: 20÷25%

  • Lepkość natryskowa
  • Spraying viscosity

    16÷18 seconds at 20ºC

  • Żywotność mieszanki
  • Pot life for the mixture

    6÷ 8 hours at 20ºC

  • Number of layers

    2 full layers; about 60 µm of dry coating.

    Gun parameters
    RP Nozzle: 1,3÷1,4mm; Pressure: 2,0÷2,2 bar.
    HVLP Nozzle: 1.3÷1,4mm; Inlet pressure: 2,0 bar.

    Caution: Follow the recommendations of the equipment manufacturer.

  • Czas odparowania
  • Flash off time

    Between layers: about 5÷10 minut
    Before baking: about 15 minut

  • Czas utwardzania
  • Curing time

    Dust dry at 20°C: 35÷40 minutes
    Baking at 60°C (temp. of panel): 30 minutes
    Ready to polish: after drying overnight.

    * Temperatures below 20°C significantly increase the drying time.

    .
  • Suszenie promieniem IR
  • IR Drying

    15÷20 minutes under short wave depending on the total thickness and type of radiator. Do not exceed maximum temperature of 60°C. Use according to the recommendations of the equipment manufacturer. Wait about 10 minutes before starting IR drying.

  • Informacja
  • Performance

    1 liter of the mixture is enough to paint 8 m2 of surface with a layer thickness of 60 μm.

  • Informacja
  • Shading

    Make sure you have covered all the surface with the clearcoat. You should only shade the surface that has been covered and treated. Use InterTroton FADE OUT THINNER to clean any dust or dirt from the surface and to level out the optical gloss differences between the older and new applied coating

  • Informacja
  • Polishing and eliminating defects

    Usually polishing is unnecessary, as the MASTER TIX HS 2:1 Acrylic Clearcoat gives the surface a perfect look immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.

  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar.
    • When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product



    

    Related products

      
    See also other products
    Wyjście 
    Go to top