C2007 UHS 2:1

Acrylic clear coat

Varianten

Farbe	Artikelnummer	Volumen	Menge pro Karton
farblos	1294	1 l	6
farblos	1307	5 l	4
Härter
standard	1295	0,5 l	6
standard	1853	2,5 l	4
schnell	1852	0,5 l	6
schnell	1469	2,5 l	4
langsam	1909	0,5 l	6
langsam	8440	2,5 l	4

Glanzgrad

Hochglanz

Technische Dokumentation

Gewichts-/Volumenrechner

Farbe:

Härter:

		ml	g
Grundierung
Härter:		0	0
Gesamtsumme der Mischung		0	0
Mindestverdünner	0%	0	0
Gesamtsumme der Mischung		0	0
Maximalverdünner	0%	0	0
Gesamtsumme der Mischung		0	0
Verdünnungswert	%	0	0
Warnung: Wert liegt nicht innerhalb der vom Hersteller angegebenen Toleranz. (Min: , Max: ).
Gesamtsumme der Mischung		0	0

Video

Description

2K acrylic clearcoat with ultra high solids content for car body repairs. Ideal for whole car body repair with perfect leveling and great resistance to UV rays and other harmful climatic conditions. The product is ready to use without the addition of thinner, easy to mix and apply.

PERFORMANCE: 1 liter of the mixture is enough to paint 10 ÷ 12 m2 of surface with a layer thickness of 50÷60 μm.

Advantages

High solids content.
Excellent coat appearance.
Very high gloss.
Easy to mix and apply (no thinner required).

Substrates

Acrylic clearcoats can be applied over:

Basecoats.
Old paint coatings in good condition after matting and degreasing.

Wichtige Informationen zur Verwendung des Produkts

degrease
Mixing ratio
2 : 1
Spraying viscosity
18 ÷ 20s / 20°C
Pot life
1,5 h / 20°C
2 layers
HVLP / RP
ø1,2 ÷ 1,4 mm
between layers
7 ÷ 8 min
before baking
15 min.
Drying time
30 min. / 60°C

Use
Paint repairs on small and large surfaces.

Mixing ratio by volume
Clearcoat: 2
Hardener: 1
Thinner for acrylic systems: 0%

Spraying viscosity
18÷20 sec at 20°C

Gun parameters
Number of layers
2 thin layers, dry film thickness: about 60μm.
RP gun parameters
Nozzle: 1.2÷1.4 mm; Pressure: 2,0÷2,2 bar.
HVLP gun parameters
Nozzle: 1.3÷1.4 mm; Inlet pressure: 2,0 bar.

Flash off time
Between layers: 7-8 min.
Before baking: 15 min.

Drying time
Drying time at 20ºC
Dust free: about 35-40 min.
Drying time at 60°C
Clear coat is ready to polish after baking for about 30 minutes and approx. 2 hours after cooling of the coating.
Temperatures below 20°C significantly increases the drying time.

IR drying
15÷20 minutes under short wave depending on the total thickness and type of radiator.
Do not exceed maximum temperature of 60°C.
Use according to the recommendations of the equipment manufacturer.
Wait about 10 minutes before starting IR drying.

Performance
1 liter of mixture is enough to cover 10÷12 m2 with a dry layer with thickness of 50÷60 μm.

Polishing and eliminating defects
Usually polishing is unnecessary, as the C2007 UHS 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.

General notes
Do not exceed recommended doses of the hardener!
The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar.
When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
The rooms should be well ventilated.
Clean the guns and equipment immediately after use.
Caution: To maintain safety, always follow the instructions given in the MSDS for the products.