C108 HS 2:1

Acrylic clear coat

Variants

ColourArt. No.Capacity Quantity per carton
transparent130861 l6
transparent13088 5 l4
Hardener for clear coat
standard13087 0,5 l6
standard130892,5 l4
fast130990,5 l6
fast131002,5 l4
slow142590,5 l6
slow142602,5 l4

Gloss grade

high gloss
C108 HS 2:1

Technical documentation

Weight/Volume Calculator

mlg
Primer
Hardener:00
Total of mixture00
Minimum thinner0%00
Total of mixture00
Maximum thinner0%00
Total of mixture00
Thinner value %00
Warning: Value is not within the tolerance given by the manufacturer. (Min: , Max: ).
Total of mixture00

Video

Description

High-quality 2K HS acrylic clearcoat for car body repairs with a low content of volatile compounds and increased scratch resistance SR (Scratch Resistant). Features high glossy finish and mechanical resistance.

PERFORMANCE: 1 liter of the mixture is enough to paint 8,5 ÷ 9 m2 of surface with a a thickness layer of 60 μm.

Advantages

  • High solids content.
  • Very high and stable gloss.
  • Paint durability and color depth.
  • High hardeness and mechanical resistence.
  • Very good overspray absorption.
  • Excellent flow and ease application.

Substrates

Acrylic clearcoats can be applied over:

  • Basecoats.
  • Old paint coatings in good condition after matting and degreasing.

Important informations

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    Mixing ratio
    2 : 1 + 0÷5%

  • Lepkość natryskowa

    Spraying viscosity
    15 ÷ 17s / 20°C

  • Żywotność mieszanki

    Pot life
    2 h 45 min. / 20°C

  • Liczba warstw

    2 layers
    HVLP / RP
    ø1,3 ÷ 1,4 mm

  • Czas odparowania

    between layers
    10 min

  • Czas odparowania

    before baking
    10 ÷ 15 min.

  • Czas utwardzania

    Drying time
    30 min. / 60°C
    (for standard hardener)

Application process

  • Zastosowanie
  • Use

    For car body repair that require a durable finish.

  • Proporcje mieszania
  • Mixing ratio by volume

    Clearcoat: 2
    Hardener: 1
    Thinner for acrylic systems: 0-5%

  • Lepkość natryskowa
  • Spraying viscosity

    15÷17 seconds at 20ºC

  • Żywotność mieszanki
  • Pot life for the mixture

    about 2 hours and 45 minutes at 20ºC

  • Liczba warstw
  • Number of layers

    Number of layers: 2 full layers; about 60 µm of dry coating.
    Gun parameters
    RP Nozzle: 1,3÷1,4mm; Pressure: 2,0÷2,2 bar.
    HVLP Nozzle: 1.3÷1,4mm; Inlet pressure: 2,0 bar.

    Caution: Follow the recommendations of the equipment manufacturer.

  • Czas odparowania
  • Flash off time

    Between layers: about 10 min
    Before baking: about 10-15 minutes

  • Czas utwardzania
  • Drying time for standard hardener

    Dust dry: about 60 min./20°C
    Baking at 60°C: (panel temp) 30 minutes
    Ready for polishing: after drying overnight.

    Temperatures below 20°C significantly increase the drying time.

  • Suszenie promieniem IR
  • IR Drying

    10÷15 minutes under short wave depending on the total thickness and type of radiator.
    Do not exceed maximum temperature of 60°C.
    Use according to the recommendations of the equipment manufacturer.
    Wait about 10 minutes before starting IR drying.

  • Informacja
  • Performance

    1 liter of the mixture is enough to paint 8,5÷9 m2 of surface with a layer thickness of 60 μm.

  • Informacja
  • Shading

    Make sure you have covered all the surface with the clear coat. You should only shade the surface that has been covered and treated. Use InterTroton FADE OUT THINNER to clean any dust or dirt from the surface and to level out the optical gloss differences between the older and new applied coating.

  • Informacja
  • Polishing and eliminating defects

    Usually polishing is unnecessary, as the C38 VHS Clear Coat 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.

  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Ask about this product



    

    Related products

    

    Check product tips

     
    See also other products
    Wyjście 
    Go to top