C38 VHS 2:1

Acrylic clear coat

Variantes

ColorNº art.CapacidadCantidad por caja
transparente130901 l6
transparente130925 l4
Endurecedor
estándar130910,5 l6
estándar130932,5 l4
rápido131010,5 l6
rápido131022,5 l4
lento142680,5 l6
lento142692,5 l4

Grado de brillo

alto brillo
C38 VHS 2:1

Video

Description

High-quality 2K acrylic clearcoat for car repairs with a very low content of volatile compounds. The short drying time (3 hours at 20 ° C) combined with the extended pot life of the mixture allows for partial and overall paiting of the entire car body.

PERFORMANCE:
1 liter of the mixture is enough to paint 10 m2 of surface with a a thickness layer of 60 μm.

Advantages

  • For the repair of small and large areas.
  • Very high solids content >55%.
  • Excellent finish.
  • Easy application.
  • Great overspray absorption.
  • Perfect flow.

Substrates

Acrylic clearcoats can be applied over:

  • Basecoats.
  • Old paint coatings in good condition after matting and degreasing.

Información importante sobre el uso del producto

  • Przetrzeć odtłuścić

    degrease

  • Proporcje mieszania

    mixing proportion
    2 : 1 + 0 +5%

  • Lepkość natryskowa

    spraying viscosity
    17 ÷ 19s / 20°C

  • Żywotność mieszanki

    pot life for the mixture
    3,5 h / 20°C

  • Liczba warstw

    1,5 ÷ 2,0 layers
    HVLP / RP
    ø1,2 ÷ 1,4 mm

  • Czas odparowania

    between layers
    5 ÷ 10 min

  • Czas odparowania

    before baking
    10 min

  • Czas utwardzania

    drying time
    3 h / 20°C
    15 min. / 60°C
    (for standard hardener)

Proceso de aplicación

  • Zastosowanie
  • Use

    For car body repair of small and large surfaces.

  • Proporcje mieszania
  • Mixing proportion per volume

    Clearcoat: 2
    Hardener: 1
    Thinner for acrylic systems: 0-5%

  • Lepkość natryskowa
  • Spraying viscosity

    17÷19 seconds at 20ºC DIN4

  • Żywotność mieszanki
  • Pot life for the mixture

    (double viscosity, the clearcoat cannot be used)
    3,5 hours at 20ºC (standard hardener)
    2 hours at 20ºC (fast hardener)

  • Liczba warstw
  • Gun parameters

    RP Nozzle: 1,2÷1,4mm; Pressure: 2,0÷2,2 bar.
    HVLP Nozzle: 1.3÷1,4mm; Inlet pressure: 2,0 bar.
    Caution: Follow the recommendations of the equipment manufacturer.
    Application:
    – 1,5 layers – 1 medium, thin layer and one full coat with 2 minutes flash off between coats to obtain a dry film thickness of 50-60 µm,
    – 2 layers – 2 full layers with a 5-10 minutes flash-off time to obtain a dry film thickness of 60-75 μm,

  • Czas odparowania
  • Flash off time for standard and fast hardener

    Between layers: 5-10 min
    Before baking: 10 min

  • Czas utwardzania
  • Drying time for standard hardener

    Dust dry: 40 min./20°C, 10 min./60°C
    Touch dry: 3 hour/20°C, 15 min./60°C
    Ready to use: 13 hours/20°C, 15 min./60°C+4 hours/20°C
    Final drying: 7 days/20°C, 15 min/60°C+4 days/20°C

  • Suszenie promieniem IR
  • IR Drying

    10÷15 minutes under short wave depending on the total thickness and type of radiator.
    Do not exceed maximum temperature of 60°C.
    Use according to the recommendations of the equipment manufacturer.
    Wait about 10 minutes before starting IR drying.

  • Informacja
  • Performance

    1 liter of the mixture is enough to paint 10 m2 of surface with a layer thickness of 60 μm.

  • Informacja
  • Polishing and eliminating defects

    Usually polishing is unnecessary, as the C38 VHS Clear Coat 2:1 gives the surface a perfect finish immediately after application. However, if some dirt inclusions appear, we recommend removing them and then polishing the surface with an abrasive compound.

  • Informacja
  • General notes
    • Do not exceed recommended doses of the hardener!
    • The best repair results can be achieved by painting at room temperature. The temperature in the body shop and the temperature of the product should be similar. When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and airways.
    • The rooms should be well ventilated.
    • Clean the guns and equipment immediately after use.

    Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

Haga una pregunta sobre el producto



    

    Productos relacionados

    

    Consulte los consejos del producto

     
    Ver también otros productos
    Wyjście 
    Go to top